Short answer: seelan (wall dampness) is fixed permanently by stopping the water at its source, removing the damaged plaster about 0.5–1 metre above the damp line, brushing two coats of a cementitious waterproofing slurry such as SikaTop-107 Seal or SikaSeal-105 onto the bare wall, and re-plastering with a waterproofed mortar (Sika-1 or Sikalite-101 in the mix). Damp-proof paint or putty on its own does not cure seelan, because the water keeps coming from behind.
Why walls get seelan in Pakistani houses
- Rising damp: the damp-proof course (DPC) at plinth level is missing or broken, so ground water climbs up the brickwork. Typical sign: a tide mark 1–3 feet above the floor and white salt (shora) on the wall.
- A wet room next door: a leaking bathroom, kitchen sink or water tank on the other side of the wall, or in the floor above.
- Rain getting in: cracks in outer plaster, a leaking roof or a parapet that collects water. Usually worse after the monsoon.
- Hidden pipes: a slow leak in a concealed water or drain pipe. If the patch stays wet in dry weather, suspect a pipe.
Step-by-step permanent treatment
- 1. Find and fix the source. Repair the pipe, regrout or waterproof the bathroom, or fix the roof first. Without this, no treatment lasts.
- 2. Remove the damaged plaster down to the brick, at least 0.5–1 m above the highest damp mark. Rake out loose mortar joints and wash off salt.
- 3. Dampen the wall (not wet) so the slurry bonds and does not dry too fast in the heat.
- 4. Brush on the waterproof slurry in two coats, the second crosswise. SikaTop-107 Seal is the flexible choice for walls that may move or crack; SikaSeal-105 is the economical multipurpose slurry.
- 5. Re-plaster with waterproofed mortar. Use diluted Sika-1 (1 part to 10 parts water) as the mixing water, or add Sikalite-101 powder at 2% of the cement weight, which is 1 kg per 50 kg bag of cement.
- 6. Cure properly for several days, then let the wall dry fully before painting. Use a breathable paint.
How much material and what it costs (Nov 2026)
- SikaTop-107 Seal: about 1 kg per m² per coat, minimum two coats. A 25 kg set (Rs. 8,000) covers roughly 12 m², about 130 sq ft of wall, so around Rs. 60 per sq ft in material.
- SikaSeal-105: 2–4 kg per m² in total. A 25 kg kit (Rs. 7,800) covers about 6–12 m² depending on thickness; the 12.5 kg kit is Rs. 3,700.
- Sikalite-101: Rs. 320 per 1 kg bag, enough for one 50 kg cement bag of plaster.
- Sika-1: Rs. 3,299 for 5 litres, which makes about 55 litres of mixing water.
Labour and the plaster itself come on top. For a full room, compare the slurry route with chemical DPC injection if the damp is clearly rising from the ground.
Mistakes that make seelan come back
- Painting or putting wall putty over a damp wall.
- Stopping the plaster removal at the visible damp line instead of going higher.
- Using plain cement-sand plaster again without a waterproofer.
- Skipping curing in summer, which cracks the new plaster.
FAQs
Diwar ki seelan ka permanent ilaj kya hai?
Pehle pani ka source band karein (pipe, bathroom ya chhat). Phir kharab plaster utarein, deewar par SikaTop-107 Seal ya SikaSeal-105 ke do coat lagayein, aur naya plaster Sika-1 ya Sikalite-101 mila kar karein. Sirf paint se seelan khatam nahi hoti.
Can I treat seelan from inside only?
Inside treatment helps only if the water source is also stopped. If rain enters from outside, treat the outer wall too.
How long before I can paint?
Let the new plaster cure and dry fully, usually 2–4 weeks depending on weather.
See also our step-by-step guide: Wall seepage and dampness treatment.